Sunday, 27 September 2015

Of Lamp Posts and Phone Boxes

Just a quick update of progress in preparing 'Shifting Sands' for the Sheffield Model Railway Society's Annual Show on October 10th. As previous posts have shown, my long-awaited aim to have lamp posts on the layout has been achieved, and they were 'planted' yesterday.


The posts have been located using some lengths of the same 3/32nd tubing that forms the centre section of the pole.  Lengths of this tubing were cut to match the distance from scenic surface to the underside of the baseboard and Araldited into a pre-drilled hole. Underneath the board, once the posts were in position, enough of the 1/16th tube that runs the full height of the light was showing to add the inner working of a chocolate block electrical connector to clamp the post in position, allowing removal if required.

Another scenic addition that has been made has only been planned for a short time, from the day after Peco announced their 7mm scale plastic kit for a classic red telephone box. This has been built as per instructions (and when they say paint before assembly, you really do need to paint the inside back wall first!), sprayed with red oxide primer and finished in Vallejo red acrylic, varnished with Testors Dullcote and lightly weathered.


The phone box has taken the place of the bench that previously stood here, with a little adjustment required to slabs and some extra grass added to hide the surgery. The previous inhabitant of the bench, assumed to be the long-suffering partner of the photographer lining up his shot, has taken up residence outside the rock emporium where she continues to read her magazine!


With the layout outside for photography I couldn't resist having a play and created this image, although all attempts to digitally add the sea in the background have so far failed!


Colin

Sunday, 20 September 2015

Illuminating Progress

Just a quick update on the new lamp posts for 'Shifting Sands'.  They have now been primed with etch primer, with the lamp base and top touched in with off-black.  A finishing touch are the asset numbers created from 4mm scale vehicle registration plate numbers.


On the top of each shade I have added the little sensors that appear on top of each light, these are from a Ratio 4mm scale swan-necked lamp set.

With a little weathering they will be ready to put in place on the layout ahead of a forthcoming appearance... details here!

Colin

Monday, 14 September 2015

See the Light

I've always planned to add some street lights to 'Shifting Sands' but finding the right design and look has taken some time. Ideally I'd like some concrete tapered columns but couldn't see an easy way to produce these (although 3D printing may of some possibilities if anyone wants to try...). Last year I spotted a light in Ulrome, on the East Riding coast, that offered some possibilities:


Now I suspect this is on private land rather than part of the council set-up, but it ticked the boxes for the '
look' I was after. What follows is not an exact copy but an 'inspired by' lamp.

Here are the raw materials, K&S 1/16" brass tubing, some larger (I believe 3/32") brass tube that telescopes over, Evergreen 1/8" styrene tubing, brass drawing pins and a Modelscene 4mm scale lamp.


The first step is to upscale the lamps from the 4mm product. Each shade was drilled in the centre to accept the drawing pin and the lamp holder was carefully cut from the post, cleaned up and drilled to accept the 1/16" tubing.


The 1/16" tubing runs through the whole height of the lamps. I cut the length of tubing in half to 6" lengths, giving a good length of tube to go through the baseboard and a lamp height of approx 125mm. I cut a 50mm length of the 3/32" tubing and soldered this in place 45mm from the top of the pole.


The final step was to add a 28mm length of the 1/8" styrene tube to form the base of the lamp post, this was drilled out with a 2.5mm drill bit at the top to overlap the brass tube and given a slight angle around the top. Both the bases and lamps were fixed in place with Araldite, although the lamp shades and drawing pins are still separate parts at this stage to aid painting.  On each base I added a 12 x 4mm inspection cover from 5 thou styrene sheet.


The lamp post are now ready to paint and plant on the layout, but that is for another day!

Colin

Wednesday, 2 September 2015

Back at the bench

You may have noticed from the three month hiatus this blog appears to have had that I've not had a lot of modelling time of late, but in those odd moments I caught I considered, or rather reconsidered, the chassis I had used under the second A1 Models loco build.  The kit is promoted for the Kato mechanism and both my kits had an appropriate baseplate in plastic for this.  Putting myself into the frame of mind of "what would I do coming to this anew with a Kato in hand?" the result was this chassis frame, caught here after overall application of grey primer and then red primer on the "buffer" beams:


This frame uses the A1 Models plastic baseplate (which I was surprised stuck OK with Humbrol liquid poly), and 40 thou styrene frames and buffer beams.  The axleboxes and springs are from Cambrian Models 4mm scale mouldings with hangers fabricated from evergreen section.  Coupler pockets from MicroTrains couplers are scratchbuilt as before and the cab interior pretty much replicates the version I built on the Bachmann frame. Cab detailing would later be appropriated from the old version.

The new frame was sneaked into the paint booth for varnish just before we went on holiday, so the Dullcote had a week to dry before weathering.  The overall result was this:


I am much happier with the way this now looks, the old frame looked a bit too 'stumpy' and I don't think that was helped by the grey paintwork.  Of course I could have just painted the old one black and saved some work....

The frame has been weathered lightly to match the loco body and highlight the spring detail, those Cambrian mouldings are quite detailed! Inside the cab the controls, cushion and driver have been transferred over from the old frame, with only minimal touching in required:


Of course, although I planned for it to be as simple as possible to describe and build, I did perhaps over-detail in places, and didn't take any progress shots of the build. So I then went on a quest to develop an even simpler version, but more about that another day!

Colin

Sunday, 31 May 2015

A few bits and bobs left over... (in honour of Dave Lister)

"There's a few bits and bobs left over, but its always the same when you do a bit of do-it-yourself, isn't it?" Wise words from the guy who mended the Chicken Soup machine on the 'Red Dwarf'...

But it is indeed true.  Having completed three Dapol Railbus/Drewery Shunter loco bashes over the years I have rather a lot of left over parts, including spare window-wide panels and the sliding doors by the plenty. Some time ago I hatched a plan to use these, plus a complete new kit, to make an O9 railbus, as previewed here in 2012. Last November I did actually start to put together the parts for this project, however, despite making up sides (one side with doors, the other without), and front ends, something didn't quite gel.

Having put all the parts to one side, on re-examination I decided not to go ahead with the railbus and I took apart many of the parts and sought out how to recycle them. The door-less sides and ends, plus roof, were re-purposed as parts for a diesel loco with Evergreen 'siding' used to make grilles, and subsequently sold on as I couldn't see me completing it any time soon...



So what to do with all those window-wide panels...  well, would you believe that the width of a window frame from a Dapol railbus kit matches almost exactly the width of the Chivers seat moulding?  You may ask how I found that out, but kicking about for ideas I somehow offered the Dapol parts up to the Chivers kit... What you see here is actually the window panel with the bottom half of the side cut off and then turned upside down so that the top panel replaces the armrest of the Chivers kit side. The roof is made from further Dapol left-overs.


Inside I have created a footwell for the middle doorways to give a bit more legroom for passengers, this modification could be applied to other Chivers conversions.


After a lot of fettling and filling, sanding etc the coach was primed and I think the overall result justified the work involved, it is almost impossible to tell it is a kit-bash. The roof is currently loose-fitted to allow access to the interior for finishing off, hence the gap!



With a few panels and all the doors still left over, I looked for a further project to use up some parts. This coach started life as eight (much modified) doors and two side panels, plus a roof offcut.  The underframe is scratchbuilt in styrene, incorporating a much cut-up wagon bogie to hold the axles. 


It is based loosely on coaches built by the Parkinson's for the Southend Miniature Railway in the 1920s (to a similar style to the Great Yarmouth/Sutton bogie stock) - but my model is somewhat larger than scale, despite which you can't actually sit a figure in it... not to worry, my plans possibly see it as a static item, awaiting restoration. A comparison with the Chivers conversion shows they are about the same height but different window lines.


Both coaches now await painting but colours and finishes depend on future use...

Colin

Monday, 18 May 2015

Come in number Eight...

I'm pleased to report that the second A1 Models locomotive is now complete, seen here posed on 'The Headshunt' diorama....


As can be seen above, I've added the windscreen wipers and number plates, and I have subsequently applied some light weathering, in the form of washes on the underframe and buffer beams and dry brushing over the grilles, bolt heads, edges etc. 


Having a play about with photo angles on the recently completed diorama.  I hadn't expected this angle to work so well!


I couldn't resist the opportunity to compare the two versions of the kit before the bigger one departs to pastures new, the smaller one is definitely closer to how I imagined this kit would look when I first suggested it to John Flower.


"I'm an industrial locomotive, I look down on him.."
"I'm a pleasure railway locomotive, I look up to him..."

Colin



Saturday, 9 May 2015

Watching 'The Headshunt' / A1 Models Hunslet Update

I don't plan to add much more to the diorama 'The Headshunt', but a couple of additions that I've made this week can be found in this update. The figure is a Phoenix example from S&D, I've had him from very early in my 7mm modelling days and was one of a couple on which I used the black undercoat painting technique. He isn't permanently attached so in theory there could be an array of alternative figures to stand here! The other addition is rubbish... a black bag full, up against the wall, this was sculpted (badly) from left over Milliput from a filling job.


But just what is that chap looking at? This maybe....


As a taster of how the diorama can be used for photography, my almost complete, second version, A1 Models 'Hunslet' poses for the camera. I was in the process of getting her prepared for a trip to Peter Leadley's Clee Valley Railway at the Cleethorpes exhibition, although there are still a few details to add and weathering to tone down the livery.  

The boffins in the Shifting Sands workshop had rigged up a suitable coupling for use on the CVR allowing the loco to run solo, its performance impressing the CVR operators.


Colin