Showing posts with label Hudson Hacking. Show all posts
Showing posts with label Hudson Hacking. Show all posts

Saturday, 14 November 2026

Hudson Hacking - The Sequel


Many years ago I built a model of the Sherwood Forest Railway's Hudson-framed open wagon, using a Roy Link Scale skip frame and a very butchered Peco wagon chassis. The whys and wherefores were documented here at the time: Hudson Hacking, but it always looked a bit perched on undersized wheels and eventually gained a proper KB Scale replacement frame regauged to 9mm gauge. It then did a long shift on 'To The End...' as a static wagon. Just before Narrow Gauge Now I thought it would make a useful extra wagon for 'Odsock Corner' and very nearly added a set of couplings. But I then stopped and had a think... 

The real wagon chassis is about as butchered as my model ways, when regauged to 15" by a previous owner, rather than move the wheels on the axles, the axles were shortened and the axleboxes were moved in from the sides of the frame and mounted on angle-iron welded to the frame. My original model had reflected this, but the rebuild hadn't.


I decided that I would now try and build a new frame that not only had recessed axleboxes, but also the correct size wheelsets. Luckily two things were in my favour - I had the original frame and had intended to use it as a scenic item, and I had a spare set of Greenwich 8mm diameter wheels. 

So I set out and made a sub-frame with a 14mm wheelbase, Dundas bearings and the scratchbuilt Hudson axleboxes that had briefly featured on my generator flat wagon. 40 thou styrene was used throughout for strength, and I added several crossmembers to make a rigid frame. I was pleased that the result was square and ran true, so it was mounted into the skip frame, with two lengths of 40 x 60 styrene across the top of the frame, to support the body. This was the same size section as those under the existing body and I intended to re-use the centre support.


It was at this stage that I had a look back at the pictures of the original model and the prototype. Oh dear... even my Peco-based version didn't have a chunky section between the sub-frame across the end. The real wagon appears quite airy there and I had blocked the view of the wheels. In addition to that my 40x60 body support beams were laid flat and the originals are upright. Some changes were effected, removing both the support beams and then the offending section. I thought this might do but it became a lot less rigid so after some thought new flat beams were added, tapered on the lower outer edge to be out of sight between the sub-frames and further support fitted between the wheelsets. 


That pink post-it is my original sketch of the sub-frame sides, I made these over-long and paired then temporarily for drilling the axle holes etc, before cutting to length. The completed underframe is seen here with the current version of the wagon for comparison, the intention is to paint up the frame and then add the body back into place. 


I may have another look at the remains of the moulded couplings as they don't match the real wagon, in model terms the holes from my original MicroTrains fitting have been filled and arrangements made for Greenwich couplers with cut-down shanks to be used.

More soon...

Colin
 

Sunday, 4 April 2021

Diorama Developments - To The End...

Diorama developments must go in pairs, as I was building the bench for 'Humberston' this piece of Slaters 7mm scale fence was also in the works. A relic of my childhood "attempts" at O-16.5 modelling it was covered in a dubious coat of glossy brown enamel paint. A bath in Dettol soon sorted this out and with a little cleaning up the piece was useable.


I had used a piece of this fencing on 'Stuck in a Siding', a diorama that I built a few years ago depicting a derelict 15" gauge coach, very much inspired by the 'Abandoned Miniatures' page on Facebook. I also used this scene to experiment with making a puddle in the fashion of Gordon Gravett. The coach largely hid the fence from view in normal conditions so here the diorama is seen without it.


For this use I had added a woodgrain effect and distressed the planking a little to make it look a little less cared for. I did the same with the recovered section, as I wanted it to match... For in an audacious bit of diorama tinkering I have extended the originally 140mm long scene to match the 220mm of 'The Path To' and 'Humberston' (I guess that makes 220mm the new "standard" length!).

I managed to get the fence to join neatly enough to fill the gaps, touch in the paint finish and add diagonal joins in the cross-members. The actual join is nearly invisible. The junk pile has been moved and supplemented with a few extra pieces including an A1 Models bonnet front. I have managed to match the hanging basket liner ground cover from the original piece, as well as adding areas of Martin Welberg weed tufts and some longer Peco tufts. To give extra variety I added some rock outcrops at the back from home-made plaster castings and concrete area in the foreground, simply card covered with Green Scene concrete texture paint, and then weathered.


The plan had been to add the skip frame flat wagon seen in a previous posting, but late on in the process I had a rethink and decided to rebody it (again!). A few years ago I built a representation of the Sherwood Forest Railway' s skip framed open wagon on a much modified RCL skip frame hiding a Peco chassis (and undersized wheels) underneath. A bit on the featherweight side it has never really been used, and at the diorama viewing angle the undersize wheels were too apparent so I have transferred the body to the the more accurate chassis. The real wagon lacks the central bar along it's length so this was also removed. The Black Dog adaptor and flat wagon body have been transferred to the chassis prepared last year as a scenic item with broken axleboxes - waste not want not!


With the wagon in place on the diorama with the original carriage the revised scene is completed, new basswood strips were added front and back to hide the join in the MDF base and with this the opportunity taken to rename the diorama 'To the End'.


An investigation has been launched into the whereabouts of the missing full stop! It was there when I put the letters on... The overall result is (I feel), a much better balanced scene than the original.


I may yet add a figure to the scene, as with 'Humberston' this helps with scale, the perils of being a multi-scale modeller!

Colin

Thursday, 19 July 2012

Hudson Hacking - Part 2

The workbench has been a relatively quiet place of late, however, a few projects are starting to come to fruition and some progress made.  The Hudson wagon chassis destined to become a model based on the Sherwood Forest Railway's open wagon has been completed, since it last appeared as a chassis only, it has progressed through this:


to this:


and completed with weathering:


On it's right is a wagon assembled from various Black Dog Mining parts, a 5ft chassis formerly under one of my scratchbuilt bodies, the cut-down chequerplate top previously on the Hudson frame and a coupler unit from the spares box.  The coupler has been modified to fit in the slot for my usual MicroTrains coupler, this wagon is perhaps intended for static display, however a swift coupler change can be facilitated if required!

The eagle eyes may notice something in the background... more on that another time.

Colin

Sunday, 29 April 2012

Hudson Hacking

It looks as if the Somerthorpe Miniature Railway's PW department has relented, as another wagon build has emerged on the workbench.  This again uses parts recycled from a previous, slightly unsatisfactory build...


This RCL Hudson frame is the one used previously under a cut-down Black Dog Mining flat top.  It didn't run to well , I had put this down to replacement wheelsets, but I have subsequently discovered that during the build (itself something of a bodge) I hadn't aligned the axle box mouldlings properly, hence a wobbly ride.  Removing the axle box mouldings in one piece was a no-go, so a slightly more innovative solution was called for....

I'll be modelling this, the PW wagon of the Sherwood Forest Railway, one of a few 15" gauge wagons I can say that I have travelled in:


This real-life Hudson-bash actually has the axleboxes mounted on some angle iron behind the main frames with with the axles shortened for 15" gauge, I'm assured it was like that when they bought it from Tal-y-Cafn.

Model wise this has allowed something of a cheat, please look away now if you are a time served O14 modeller...


Yes, that is a much butchered Peco chassis living under there!  I was inspired to work this way after the success of the Peco/Black Dog adaptor under the 'Loco Coal' wagon, where I see the frame as a 'veneer' over the Peco chassis.  I this case I also slimmed down the recovered RCL axleboxes and glued them over the Peco axleguards, shorn of their N gauge detail.  Once the glue was set the axleguards were cut and filed to the same shape as the axleboxes, completing the illusion.  From normal viewing angles the deception is not visible, and the fact that the wheels are too small isn't noticeable.

Progress with the other two wagons has reached the varnishing stage, whilst some loads are being assembled from the spares box: